Installing the corrugations on the hood: how to put on or inserted into, which is the diameter

Corrugation - pipe which is used as a duct. On it are the evaporation or combustion products. It is installed between the equipment. Due to the corrugations in the room is always clean air, as there is a ventilation when connected to a kitchen hood. As for appearance, it may be rectangular or circular. The first of these is usually operated at the production plants. Another same model can be found in a residential area. Possible composition: plastic, galvanized or stainless steel, are least likely to occur textiles. Installing the corrugations on the hood a sure way to keep the freshness of the kitchen.

species

The corrugations have several varieties:

1. Plastic. A budget option. There are many models of this type. But a common characteristic is the least air resistance, which is generated inside the tube. It is easy to wash, works fairly quiet.
   instagram viewer
   ATTENTION! It is worth remembering the fragility and possible harm to human health, as a large amount of smoke when ignited. In addition, of the cheapest devices can reach an unpleasant odor. Installation is made difficult. Afraid of high temperatures.
2. Aluminum. Not very heavy, a great chance for long-term performance, portability, high-temperature characteristics. However, during operation may issue specific sounds and increased vibration. Inconveniences arise during cleaning.
3. Insulated. Its feature - the presence of the foil layer with a mineral wool. This type can be set to any hood.
4. Other. All of these shortcomings of previous models are absent (smell, noise and flammability, lifetime) + resistant. But this kind does not come cheap. They can afford not everyone.

What are the diameters of the corrugations for drawing

There take most running corrugations, the value is 100 mm, 125 mm and 150 mm (for kitchen hood). In industrial same can extract and 200 mm, 250 mm, 300 mm. The choice depends directly on the power unit. Should take into account the diameter of the drawing, respectively, they must be the same. If you want a large diameter, it is necessary to find the adapter at the same time, to dock with the neck. The dimensions of the corrugations on the hood has a few classic options. The kitchen hood instructions you can always find the minimum value. The most commonly used 100 mm and 120 mm. If you still are not able to choose the size, use the larger, especially good this kitchen: the noise will be reduced due to low flow rate. With reduced diameter, the air will be pushed, experiencing difficulty.

installation

How to Install a corrugation on the hood in the kitchen yourself and why? To air updated regardless of whether the extractor fan or not, you should connect the corrugation through the bars to vent. Because there is a compartment opening to the duct and for removing air. When installing you must also take into account the technical characteristics - size and length of the pipe, otherwise all the work done would be inappropriate. Be aware of the quality and reliability of the chosen material. In addition, it is better when everything is done in the same style, for interior. It is understood that the price does not guarantee the proper implementation of the installation, so the study kollyatsiyu. There are written, how to install the exhaust duct for the kitchen.

How to choose the size

It is necessary to measure the entire length of tape. And take into account the route, which will take place the duct. For example, it is possible path through the cabinet, along the walls or on the ceiling. After the calculations should be added to the total length of more around 10 to 15 percent. This is an important point, before connecting to the corrugated hood.

IMPORTANT! Specify the size of the corrugations in the stretched form. It is worth taking a long margin. The ideal is 3 meters, but even if it appears quite superfluous length, it can not hurt.

In the reverse situation, when a lack of material can be attached via a missing piece of tape, but this option would reduce airway patency. Should resort to this only in extreme cases. With the least number of corners, but with a higher degree extractor is able to work much more consistently.

How to fix the corrugation on the hood

In order to somehow connect the corrugated stretch, you will need:

• corrugated
• screws
• clamps for fixing the sleeve or soft wire
• grille for ventilation or adapter
• silicone sealant
• Adapter not found a corrugation appropriate size

How to strengthen the corrugation to the hood, after all of the tools are ready:

1. Before the work should be cleaned ventilation in the apartment
2. To get started drag a corrugation on its length, check the component elements. Avoid kinking, while air draft will remain good.
3. Using sealant grease neck drawing
4. Put corrugation and fix a collar, but if not, then wrap the wire.
5. It is necessary to pave the way to the end of the ventilation holes
6. Fix the screws under the ventilation grille
7. Then wear corrugation sealant
8. Attach the work clamp
9. Check the exhaust system connecting the appliance to the network. This is done as follows: Turn the hood to maximum power, and now take a sheet of paper and bring it to the bottom of the grid. Sign the correct mount is holding a leaf - hence, air is sucked in. All problem is how to put on a corrugation on the hood, is solved.

REFERENCE! Do not wipe the outer surface, it will save you from prying unwanted odors.

You must know that the vent is necessary. We can not close the mine completely.

If you do not want the flute has been on public display, it is possible to hide it. How to insert a corrugation in the inside hood to make it invisible? This is easily done with the help of doors hinged cabinets, decorative boxes or other items. To disguise his need to choose the color tone of the furniture. To make the harmony, try to arrange everything on the basis of style cuisine. Another option is to establish a lining. It can be formed in the enclosure circuit thereby will provide stealth ventilation. It is not difficult to build and inside the kitchen set. However, thus it will be lost a lot of space, but also added the holes that need to be cut through.

If you do not want to understand how to extract attached corrugation, you can simply order a professional installation. Especially if the kitchen was done with the hood on request. Then, the installation of the corrugations for drawing can not go through the standard procedure.

Why the need for installation of the corrugations on the hood

Using corrugated pipe is good because they have many advantages. For example, most can afford to install them, and installation, as it turned out, quite simple. In addition, they have a wide range of types and sizes and small weight in a compressed state. Endurance at high temperatures, thereby not subjected to combustion. It is possible to install both indoors and outdoors, which indicates the functionality. Placed in different planes, are used in different parts of systems. Only need to be concerned once as the freshness of the room is guaranteed for a long time.